Prestressed Bolt Connection

MITCalc Bolted Connections is designed for a geometrical design and strength check of a prestressed bolt connection, loaded by static or cyclic loading resp. , acting both in the axis of the bolt and in the plane of the connected parts.

Calculation Slender Strut (Column) Buckling

MITCalc Buckling is designed to calculate the optimum cross-section and perform strength check of slender struts strained for buckling

Plates Deflection and Stress

This calculation deals with the deflection, stress and variation of forces in the loaded flat plates.

Profiles Static Characteristics

MITCalc Profiles solves area characteristics of common profiles and mass characteristics of solids created by drawing or rotation of the profile.

Shafts Design and Calculation

The calculation is designed for geometrical designs and complex examinations of shafts.

Design and strength control of statically loaded welded connections

MITCalc Welded Connections is intended for the geometrical design and strength control of statically loaded welded connections of machine structures manufactured from carbon steels.

Simple-Span Members Subjected To 1-8 Moving Wheel Loads

MOVLOADS is a spreadsheet program written in MS-Excel for the purpose of analysis of simple-span members subjected to from one up to eight moving wheel loads with up to seven wheel spacings.

LRFD External Stability Analysis

Designing an MSE wall requires consideration of the geometric configuration and reinforcement requirement to ensure external and internal stability.

Pile Group Analysis for a Rigid Pile Cap/Mat

PILEGRP is a spreadsheet program written in MS-Excel for the purpose of analysis of pile groups with rigid caps using the elastic method.

Bending Moments, Axial and Shears Forces in a Plane Frame

A Plane Frame Analysis for bending moments, axial and shears forces in a plane frame structure under point loads, UDL's, linearly varying distributed loads (soil pressures) and moments.

Pole Foundation Analysis

POLEFDN is a spreadsheet program written in MS-Excel for the purpose of analysis of a pole foundation assuming the use of a rigid round pier which is assumed free at the top and subjected to lateral and vertical loads.

Preliminary Design Of Prestressed Concrete Bridge Girder

This spreadsheet performs preliminary analysis of a precast prestressed bridge girder at the prestress transfer and service stages.

Prestressing Losses in Post-Tensioned Tendon

Calculates elongations and prestress losses due to friction and anchor set of three-dimensional post-tensioned tendon.

Moving truck analysis for bridges with simple or continuous spans

Moving truck (up to 20 axles) analysis for bridges with simple or continuous spans (up to 5). Envelopes (M & V) and support reactions.

Section Properties Of A Riveted Plate Girder

Section properties of a riveted plate girder to BD 56/10 and BS5400-3:2000 with facility to allow for corroded elements.

Roof Steel Deck Analysis & Design

ROOFDECK is a spreadsheet program written in MS-Excel for the purpose of analysis and design of roofs with steel deck.

Cross-Sectional Properties Of Structural Members

Calculates structural properties of general cross-section. Also calculates torsional properties of thin-walled section including shear center and warping moment of inertia.

Investigation Of Reinforced Concrete Column Section

ShortCol computes ultimate strength of reinforced concrete column subjected to combined axial force and bending moment.

Load Combinations and Minimum/Maximum Force Envelopes

Creates load combinations and finds maximum/minimum force envelopes for structural members.

Section Properties of Solid Irregular Sections by Co-ordinate Geometry

This Proforma calculates the section properties of an irregular shaped cross section by co-ordinate geometry.

You are on page 3 of 4

396814 hitsWest Point Bridge Designer v2016

Bridge Design Contest is a nationwide Internet-based competition intended to promote math, science, and technology education in US. West Point Bridge Designer provides you with the tools to model, test, and optimize a steel highway bridge.

46322 hitsLTBeam v1.0.11

LTBeam is a software which deals with the elastic Lateral Torsional Buckling of Beams under bending action about their major axis.

24660 hitsFTOOL v4.0

Ftool provides a simple analysis program that merges, in the same interface, resources for effective creation and manipulation of the model, linked to a fast and effective code for visualization of the results.

22683 hitsETABS v19

ETABS is the solution, whether you are designing a simple 2D frame or performing a dynamic analysis of a complex high-rise that utilizes non-linear dampers for inter-story drift control.

22259 hitsSAP2000 v22

From its 3D object based graphical modeling environment to the wide variety of analysis and design options completely integrated across one powerful user interface, SAP2000 has proven to be the most integrated, productive and practical general purpose structural program on the market today.